EF 88-91 Honda Civic/Crx H22A Motor Mount Kit
This kit is for the hardcore EF enthusiast wanting the ultimate engine swap. This kit is perfected for the ultimate driving experience and it will keep the power on the ground where it needs to be. No violent shaking or vibration. Just a smooth, accelerating driving experience.
Works with 88-91 Civic Hatchback All Models, Dx, Std, Si. Also works with 88-91 CRX All Models, Hf, Dx, Si and 88-91 Civic Sedan All Models, Dx, Std, Ex.
This motor swap will require some work. As we all know this is not a direct drop in. AC is not possible without extensive modification. It is recommended to run an alternator only crank pulley. The passenger side stock mount on the chassis will need to be removed and the new passenger side chassis mount will need to be welded or bolted in. You may have the engine/transmission in and out of the car several times to get it located absolutely correct. Installation instructions will be included that will give you all critical measurements. Also included is the custom alternator mounting and tensioner brackets which puts the alternator closer to the engine. It also is much lighter and better looking then the bulky factory cast iron piece. Don’t hesitate to email me with any questions on the installation. If you are local and would like us to do the install we can do it!
Below are a couple pictures of a customers H22A Crx that was built over in the U.K.
EF 88-91 Civic/Crx H22A Motor Mount Kit complete kit includes:
(1) Driver side motor mount
(1) Rear engine mount
(1) Rear chassis mount
(1) Weld in or bolt in passenger side chassis mount, prefer weld in.
(1) Passenger side motor mount
(1) Alternator upper bracket and bolts
(1) Tensioner bracket for upper (your choice of bracket for either H series or D series alternator). Pictured below.
(1) Clutch cable/hydro conversion lever system (pictued below)
(1) Passenger side chassis new hole template only for 90-93 DA H22A motor mount kit
$459+$15 for shipping = $474 shipped US
- If you want the Lower H22A Alternator/Tensioner kit for either H or D series alternators instead of the Upper please let us know an additional $20 will be added onto the motor mount kit price.
The Polyurethane 70A grade inserts are easily replaceable unlike most other kits. Choice of Black or Red insert colors. Powder coating finish is semi gloss black.
Upon purchase please include the following:
Year and Model of Car... Ex: 90 Crx HF
Your selection of Red or Black inserts...
Your selection of Upper H or D series Alternator/Tensioner Kits...
EF H22A Key Parts List:
Swaping out Front Hub/Spindle/Knuckle and Caliper and Rotor to a 90+ Acura Integra is a must. Just like any B series swap. Any Honda/Acura junkyard will have them for a decent price.
- 90-01 Acura Integra Front Hub/Spindle/Knuckle/Caliper/Rotor
Axle Combo:
- 88-89 Acura Integra driver side axle off shelf parts store.
- 90-93 Honda Accord Ex or Lx model midshaft
- 88-89 Acura Integra passenger side axle that has been cut down 1/2" on the shaft and has an Accord 90+ Inner joint put on it. Raxles.com sells this 1 custom axle. Ask for Marty.
Cable Shifter Assembly:
90-93 Honda Accord cable shifter assembly and cables will work with the swap or 92+ Prelude. Make sure you keep all the washers and clips organized.
Wiring Options:
Obd0-Obd1 conversion is a must. 2 ways to go about it pick up a RYWIRE (Rywire.com) Obd0-Obd1 jumper harness and doing the wiring your self, mostly extending wires to reach on the H22 engine and maybe a few sensor swaps. Roughly about a day's work. Easier to do the wiring adjustments when engines out of car. Or last option is the easiest and which I prefer saves wiring headaches and mistakes. Purchasing a custom RYWIRE (Rywire.com) Obd0-Obd1 EF H22A plug and play harness already made. Took me 10 min to put on :). Just send them your factory EF engine harness and the H22A engine harness and about $400 and they will make your custom harness. Looks real nice and simple I use them for all our EF H22 swaps. I can't say enough good about them.
EF 88-91 Civic/Crx H22A
Packaged Deal
Includes our EF H22A motor mount kit and our EF H22A Traction Bar System. Specially made for the swap. Our EF Traction Bar System is a replacement of the stock cross member. The stock cross member will not work with the swap so this is a must have. Either now or when almost completion of the swap. This Package Deal also has a savings off the listed price. Pictured Below.
$780 shipped US
